506 - Slurry Seal - Revision history

SchaeferS: Removed 2012 Spec Book tagline at top of page

2021-12-15T22:17:43Z

Removed 2012 Spec Book tagline at top of page

SchaeferS: /* MEASUREMENT AND PAYMENT */

2021-05-06T20:31:35Z

MEASUREMENT AND PAYMENT

Greenes2 at 15:52, 27 June 2014

2014-06-27T15:52:54Z

Rinarda at 19:02, 24 July 2013

2013-07-24T19:02:45Z

Rinarda at 17:50, 25 June 2013

2013-06-25T17:50:22Z

Rinarda at 18:58, 13 June 2013

2013-06-13T18:58:21Z

Rinarda at 18:46, 13 June 2013

2013-06-13T18:46:46Z

Greenes2: Created page with "506 - Slurry Seal * 506.01 - Materials * 506.02 - Equipment * 506.03 - Pre-Paving Meeting * 506.04 - Construction * 506.05 - Delayed Acceptance"

2013-05-22T15:48:29Z

Created page with "506 - Slurry Seal * 506.01 - Materials * 506.02 - Equipment * 506.03 - Pre-Paving Meeting * 506.04 - Construction * 506.05 - Delayed Acceptance"

New page

506 - Slurry Seal

* [[506.01 - Materials]]
* [[506.02 - Equipment]]
* [[506.03 - Pre-Paving Meeting]]
* [[506.04 - Construction]]
* [[506.05 - Delayed Acceptance]]

← Older revision		Revision as of 22:17, 15 December 2021
Line 4:		Line 4:
	<center><span STYLE="font: 40pt arial;">'''Slurry Seal'''</span></center>		<center><span STYLE="font: 40pt arial;">'''Slurry Seal'''</span></center>

−	~~<center>[http://mdotcf.state.mi.us/public/specbook/files/2012/506%20Slurry%20Seal.pdf 2012 STANDARD SPECIFICATIONS FOR CONSTRUCTION - SECTION 506]</center>~~

← Older revision		Revision as of 20:31, 6 May 2021
Line 32:		Line 32:

	[[Category:Construction Manual]]		[[Category:Construction Manual]]
		+	[[Category:Division 5]]
		+	[[Category:Section 506]]

@@ Line 9: / Line 9: @@
 ==[[#GENERAL|GENERAL]]==
+<span style="color: red"> -Reserved- </span>
 {{top}}
@@ Line 64: / Line 15: @@
 ==[[#MATERIALS|MATERIALS]]==
-The asphalt emulsion must be certified and supplied by an approved supplier.  The mix design and quality control testing is the responsibility of the Contractor.  The MDOT inspector must ensure that a proper mix design and JMF have been established and that the Contractor is performing the specified quality control testing.  The inspector must also ensure that the proper daily documentation is received from the Contractor.
+<span style="color: red"> -Reserved- </span>
 {{top}}
@@ Line 70: / Line 21: @@
 ==[[#CONSTRUCTION|CONSTRUCTION]]==
+<span style="color: red"> -Reserved- </span>
 {{top}}
@@ Line 119: / Line 27: @@
 ==[[#MEASUREMENT AND PAYMENT|MEASUREMENT AND PAYMENT]]==
+<span style="color: red"> -Reserved- </span>
 {{top}}
 [[Category:Construction Manual]]

@@ Line 7: / Line 7: @@
-==GENERAL==
+==[[#GENERAL|GENERAL]]==
-===Pre-Paving Meeting===
+===[[#Pre-Paving Meeting|Pre-Paving Meeting]]===
 A pre-paving conference between the Contractor and the Engineer should be held on site prior to beginning work.
@@ Line 62: / Line 62: @@
 {{top}}
-==MATERIALS==
+==[[#MATERIALS|MATERIALS]]==
 The asphalt emulsion must be certified and supplied by an approved supplier.  The mix design and quality control testing is the responsibility of the Contractor.  The MDOT inspector must ensure that a proper mix design and JMF have been established and that the Contractor is performing the specified quality control testing.  The inspector must also ensure that the proper daily documentation is received from the Contractor.
@@ Line 68: / Line 68: @@
 {{top}}
-==CONSTRUCTION==
+==[[#CONSTRUCTION|CONSTRUCTION]]==
-===Site Preparation===
+===[[#Site Preparation|Site Preparation]]===
 All loose materials, vegetation, dirt, mud and other objectionable material shall be removed from the surface prior to placing the mixture.  If a bond coat is required, it shall be allowed to cure before placement of the mixture is permitted.
@@ Line 77: / Line 77: @@
 {{top}}
-===Weather Limitations===
+===[[#Weather Limitations|Weather Limitations]]===
 Placement of the mixture is not permitted if there is rain, or threatening weather, and temperatures are forecast to be below 32°F (0°C) within 24 hours of completion of the work.  The mixture shall not be placed if the air or pavement temperature is below 45°F (7°C).
@@ Line 83: / Line 83: @@
 {{top}}
-===Traffic Control===
+===[[#Traffic Control|Traffic Control]]===
 Traffic shall not be allowed on the mixture until it has cured sufficiently to prevent pick up by vehicle tires.
@@ Line 89: / Line 89: @@
 {{top}}
-===Equipment===
+===[[#Equipment|Equipment]]===
 Equipment shall be safe, environmentally acceptable and capable of producing a specification product.  A typical product will have some, or all, of the following equipment on the project.
@@ Line 95: / Line 95: @@
 {{top}}
-====Slurry Seal Mixer====
+====[[#Slurry Seal Mixer|Slurry Seal Mixer]]====
 The slurry seal mixing machine shall be a continuous flow mixing unit with calibrated controls capable of delivering accurately predetermined proportions of aggregate, water and asphalt emulsion to the mixing chamber, and of discharging the thoroughly mixed product on a continuous basis.  No violent mixing will be permitted.  The aggregate shall be wetted in the pug mill immediately prior to mixing with the emulsion.
@@ Line 105: / Line 105: @@
 {{top}}
-====Spreading Equipment====
+====[[#Spreading Equipment|Spreading Equipment]]====
 Attached to the mixing machine shall be a mechanical type single squeegee distributor equipped with flexible material (the drag) in contact with the pavement surface to prevent loss of slurry and adjustable in width with a flexible strike off.  This drag shall not cause grooving of the slurry.  It shall be kept clean and no material buildup will be allowed.  The drag type, burlap or other textile, will be approved by the Engineer and it shall be changed as frequently as need, or as designated by the Engineer.
@@ Line 111: / Line 111: @@
 {{top}}
-====Miscellaneous Equipment====
+====[[#Miscellaneous Equipment|Miscellaneous Equipment]]====
 Hand squeegees, shovels and other equipment shall be used as necessary to perform the work.  Cleaning equipment, such as power brooms, air compressors, water flushing equipment and hand brooms should be adequate for surface preparation.
@@ Line 117: / Line 117: @@
 {{top}}
-==MEASUREMENT AND PAYMENT==
+==[[#MEASUREMENT AND PAYMENT|MEASUREMENT AND PAYMENT]]==
-===Delayed Acceptance===
+===[[#Delayed Acceptance|Delayed Acceptance]]===
 The Contractor is responsible for placing a uniform product.  This type of work has a 30 day delayed acceptance procedure so that any major problems will be corrected by the Contractor before the project can be accepted.  In most cases, the inspector has little to do with the slurry operation itself, but must ensure that traffic control is conducted properly and that all safety rules are followed.
@@ Line 127: / Line 127: @@
 {{top}}

@@ Line 60: / Line 60: @@
 |}
+{{top}}
 ==MATERIALS==
@@ Line 66: / Line 66: @@
 The asphalt emulsion must be certified and supplied by an approved supplier.  The mix design and quality control testing is the responsibility of the Contractor.  The MDOT inspector must ensure that a proper mix design and JMF have been established and that the Contractor is performing the specified quality control testing.  The inspector must also ensure that the proper daily documentation is received from the Contractor.
 ==CONSTRUCTION==
@@ Line 74: / Line 75: @@
 All loose materials, vegetation, dirt, mud and other objectionable material shall be removed from the surface prior to placing the mixture.  If a bond coat is required, it shall be allowed to cure before placement of the mixture is permitted.
 ===Weather Limitations===
@@ Line 79: / Line 81: @@
 Placement of the mixture is not permitted if there is rain, or threatening weather, and temperatures are forecast to be below 32°F (0°C) within 24 hours of completion of the work.  The mixture shall not be placed if the air or pavement temperature is below 45°F (7°C).
 ===Traffic Control===
@@ Line 84: / Line 87: @@
 Traffic shall not be allowed on the mixture until it has cured sufficiently to prevent pick up by vehicle tires.
 ===Equipment===
@@ Line 89: / Line 93: @@
 Equipment shall be safe, environmentally acceptable and capable of producing a specification product.  A typical product will have some, or all, of the following equipment on the project.
 ====Slurry Seal Mixer====
@@ Line 98: / Line 103: @@
 An approved means of measuring all materials used in each slurry seal batch shall be provided by the Contractor and made accessible to the Engineer.
 ====Spreading Equipment====
@@ Line 103: / Line 109: @@
 Attached to the mixing machine shall be a mechanical type single squeegee distributor equipped with flexible material (the drag) in contact with the pavement surface to prevent loss of slurry and adjustable in width with a flexible strike off.  This drag shall not cause grooving of the slurry.  It shall be kept clean and no material buildup will be allowed.  The drag type, burlap or other textile, will be approved by the Engineer and it shall be changed as frequently as need, or as designated by the Engineer.
 ====Miscellaneous Equipment====
@@ Line 108: / Line 115: @@
 Hand squeegees, shovels and other equipment shall be used as necessary to perform the work.  Cleaning equipment, such as power brooms, air compressors, water flushing equipment and hand brooms should be adequate for surface preparation.
 ==MEASUREMENT AND PAYMENT==
@@ Line 117: / Line 125: @@
 If the inspector notices a nonuniform application, any traffic control or safety violations, the Contractor must be notified immediately.  If the Contractor does not correct the violation, the project should be stopped.

@@ Line 2: / Line 2: @@
 <center><span STYLE="font: 60pt arial;">'''506'''</span></center>
-<center><span STYLE="font: 40pt arial;">'''Slurry seal'''</span></center>
+<center><span STYLE="font: 40pt arial;">'''Slurry Seal'''</span></center>
 <center>[http://mdotcf.state.mi.us/public/specbook/files/2012/506%20Slurry%20Seal.pdf 2012 STANDARD SPECIFICATIONS FOR CONSTRUCTION - SECTION 506]</center>

@@ Line 1: / Line 1: @@
-* [[506.01 - Materials]]
+<center><span STYLE="font: 60pt arial;">'''506'''</span></center>
-* [[506.02 - Equipment]]
-* [[506.03 - Pre-Paving Meeting]]
+<center><span STYLE="font: 40pt arial;">'''Slurry seal'''</span></center>
-* [[506.04 - Construction]]
-* [[506.05 - Delayed Acceptance]]
+<center>[http://mdotcf.state.mi.us/public/specbook/files/2012/506%20Slurry%20Seal.pdf 2012 STANDARD SPECIFICATIONS FOR CONSTRUCTION - SECTION 506]</center>