Search results

• Main Page
  <center><span STYLE="font: 15pt arial;">''Construction Field Services Division''</span></center> !Updated!! Division !! Section !! Summary !! What Changed
  67 KB (8,623 words) - 17:18, 11 April 2024
• 803 - Concrete Sidewalk, Ramps, and Steps
  [[Category: Division 8]]
  3 KB (465 words) - 11:50, 19 January 2022
• 802 - Concrete Curb, Gutter, and Dividers
  A low slump concrete 1/8 inch (about 2 mm) will be needed for proper slipforming. Only an occasiona ...d before the concrete sets. For the balance of the curb, a tolerance of 3/8 inch in 10 foot (10 mm in 3 m) is permitted. If the slipform machine is fu
  12 KB (1,916 words) - 11:49, 19 January 2022
• 302 - Aggregate Base Courses
  Additional depth checks will be taken 25 feet (8 m) each way from the original and the average of the three depth checks wil Additional depth checks at 25 feet (8 m) intervals each way will be taken until achieving a depth of less than 1
  6 KB (873 words) - 14:24, 16 February 2022
• Construction Value Engineering Change Proposal (VECP)
  ...gh the Construction Operations Engineer in the Construction Field Services Division. The VEDT membership will consist of the following individuals (or their de ::e. Administrator of the Development Services Division (if a local agency project)
  9 KB (1,297 words) - 14:57, 11 October 2022
• Help:Contents
  The bulk of the information will typically be under the construction sub-division for each section. ...registered) can make a suggestion to the Content Manager for a particular division:
  10 KB (1,538 words) - 12:26, 22 August 2022
• Dev Page
  <center><span STYLE="font: 15pt arial;">'''Construction Field Services Division '''</span></center> !Updated!! Division !! Section !! Summary !! What Changed
  28 KB (3,726 words) - 16:02, 8 March 2023
• Section 701 - Portland Cement Concrete for Structures
  ...e-foaming (air- detraining) admixtures. Furnish concrete containing 5.0 to 8.0 percent entrained air, except as follows: ::'''1.''' Provide an entrained air content of 5.5 to 8.5 percent for concrete containing Type F or Type G admixtures;
  12 KB (1,593 words) - 13:11, 26 July 2022
• 820 - Traffic Signals
  ...old formed members must be at least 1.5 times the material thickness (or 3/8 inches). [[Category: Division 8]]
  9 KB (1,266 words) - 15:59, 2 April 2024
• 808 - Fencing
  [[Category: Division 8]]
  6 KB (864 words) - 12:42, 19 January 2022
• 804 - Concrete Barriers and Glare Screens
  [[Category: Division 8]]
  6 KB (929 words) - 11:50, 19 January 2022
• Division 7 Supplemental Information
  <center><span STYLE="font: 40pt arial;">'''Division 7 Supplemental Information'''</span></center> ...Bridge Decks Concrete Depth Measurements, for all bridge deck pours. See Division 706 of the Construction Manual for a sample form and instructions. Concret
  33 KB (4,932 words) - 16:38, 12 May 2021
• 807 - Guardrail, Guardrail Terminals, and Miscellaneous Posts
  ...recommended to establish proper line and grade. Vertical tolerances of 5.8 inch (15 mm) measured off a compacted surface or 1-1/4 inch (30 mm) measure [[Category: Division 8]]
  7 KB (988 words) - 10:53, 8 April 2024
• 823 - Water Mains
  :##Place bedding in maximum lifts of 8 to 12 inches using approved trench backfill material as indicated in the pr [[File:823-8.jpg|600px|thumb|center|'''Figure 8 - Pressure Test''']]
  18 KB (2,799 words) - 14:01, 27 September 2023
• 603 - Concrete Pavement Restoration
  ...ent while drawing it across the repair. Any high or low spots exceeding 1/8 inch will be corrected. Recheck after corrections are made. ...t no excess raveling or spalling occurs. All edging will be done with a 1/8 inch to 1/4 inch radius along the entire perimeter before texturing.
  23 KB (3,714 words) - 10:16, 13 September 2023
• 402 - Storm Sewers
  * Blisters where the surface is broken or which project more than 1/8 inch (3 mm) above the surface. * Variations of more than 1/8 inch (3 mm) per lineal foot (300 mm) in alignment of pipe intended to be st
  16 KB (2,323 words) - 17:47, 12 January 2022
• 715 - Cleaning and Coating Existing Structural Steel
  The Construction Field Services Division (CFS) maintains a recommended procedure guide for damaged coating repair th :EGLE, Waste and Hazardous Material Division
  33 KB (4,797 words) - 11:46, 25 April 2023
• 718 - Drilled Shafts
  ...he length of the cage for #8 bar or smaller, and 10’ for bars larger than #8 to ensure a minimum annular space of 3 inches between the outside of the ca ...anner, as not to cause racking or distorting of the tied cage. See Figure 8 for a typical reinforcement cage being lowered into the completed shaft.
  28 KB (4,324 words) - 11:40, 25 April 2023
• 709 - Timber Sturctures
  ...lumber beams. Most beam type superstructures consist of sawn lumber 4 to 8 inches wide and 12 to 18 inches deep, spaced 3 feet or less apart. The dec ...surface typically is hot mixed asphalt. The panels are typically between 8 and 16 inches. deep. This structure type can be used for clear spans up to
  18 KB (2,669 words) - 16:33, 10 January 2024
• 1004 - Portland Cement Concrete Mixtures
  <center>8</center> <center>8</center>
  21 KB (3,052 words) - 16:41, 22 November 2023

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)